High Pressure Fuel Pump Fit BMW N54 N55 Engine 335i 535i 640i X3 X5 #13517616446

  
For 11-11 BMW 1 Series M 3.0L 6 Cyl. For 08-12 BMW 135i 3.0L 6 Cyl. For 07-12 BMW 335i 3.0L 6Cyl. For 07-08 BMW 335xi 3.0L 6 Cyl. For 09-12 BMW 335i xDrive 3.0L 6 Cyl. For 08-12 BMW 535i 3.0L 6 Cyl. For 10-12 BMW 535i GT 3.0L 6 Cyl. For 11-12 BMW 535i GT xDrive 3.0L 6 Cyl. For 08-08 BMW 535xi 3.0L 6 Cyl.

For 09-12 BMW 535i xDrive 3.0L 6 Cyl. For 12-12 BMW 640i 3.0L 6 Cyl. For 11-12 BMW 740i 3.0L 6 Cyl. For 11-12 BMW 740Li 3.0L 6 Cyl.

For 11-12 BMW X3 xDrive35i 3.0L 6 Cyl. For 11-12 BMW X5 xDrive35i 3.0L 6 Cyl. For 08-12 BMW X6 3.0L 6 Cyl.

For 09-16 BMW Z4 SDrive35i/ SDrive35is 3.0L 6 Cyl. Vehicle compatibility charts are for REFERENCE ONLY.

Check your vehicle with OEM below to match your needs. 13517616170, 13517585655, 13517592881, 13517594943, 13517596123, 13517613933, 13537537320, 13517616446, 13517616194. 100% quality assurance tested, more responsive, less expensive, easier to install.

This is the most up to date version of this fuel pump. Accurately and precisely spray the proper amount of fuel into the engine. Material: made of high quality Iron. 1x High Pressure Fuel Pump. Re-move fuse 70 in the glovebox, take off the negative battery. Re-move upper filter housing and side covers. Loosen hose clamp, remove air filter. Loosen hose clamp, bolt and electrical connector from.

Re-move the air charge tube from throttle body. Re-move the plastic vacuum hose from the bottom of the valve by squeezing the plastic ring and pulling off.

Re-move the four throttle body bolts and pull loose from intake manifold. Push to side out of the way. Grab the wiring harness and pull out and off of mounting bracket. Push out of the way.

Disconnect engine block electrical connector behind fuel pump and from back of fuel pump. Re-move the electrical connection, wiring bracket. Re-move vacuum line that runs from the cylinder head cover to the auxiliary vacuum pump.

Unscrew the nuts anchoring the intake manifold and re-move it. Loosen the nut, Remove the two wiring harness bracket bolts, pull rear fuel line. Loosen the nut, disconnect the top fuel line from fuel rail then remove fuel line from engine.

Unscrew the three mounting bolts, remove old fuel pump from vehicle. Verify the new fuel pump comes with a new o-ring before installing. Make sure the auxiliary vacuum pump (where fuel pump mounts to) is clean. Install the new BMW high pressure fuel pump. Reinstall fuel lines, intake manifold, throttle body, air intake and cabin filter.

Start car and test system. No installation guides are included, we highly recommend to seek professional installation.

Will come with everything you see in the picture. Please allow difference due to manual measurement. The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. For any inquiries or special requests such as larger amount ordering please write to us.